GE Deep Fill Washer Stuck On Sensing

Is your GE Deep Fill washer stuck when it goes into sensing mode? Don’t worry; this is quite common.

This normally indicates a fault in the settings or somewhere in the washer’s components that causes it to freeze when it gets into that mode.

In this guide, I will discuss some problems and the possible solutions you can apply to ensure your washer doesn’t get stuck in the sensing mode again and you can clean your laundry without any hiccups.

Let’s get started.

Reasons	Solutions
GE Deep Fill washers getting stuck on sensing	Clean or replace the water filter
mode due to faults in settings or components	Repair any gaps or blockages in the drain line
	Clean or replace the drain pump
	Clean or replace the water inlet valve
Common problems causing this issue:	Test the lid switch with a multimeter and replace if necessary
Water drainage faults	Diagnose the shift actuator with a diagnostic test and replace it if necessary
Faulty lid switch	Replace the faulty timer
Defective shift actuator	Check and correct any incorrect settings
Timer issues	Perform a reset by unplugging the washer for a minute and opening and closing the lid six times within 12 seconds
Incorrect settings	Contact a professional technician if the issue persists. Troubleshooting these issues can ensure smooth operation of the GE Deep Fill washer

5 Ways to Fix GE Deep Fill Washer Stuck On Sensing

1. Fix Drainage System

When your GE washing machine gets stuck in sensing mode, a common cause is poor drainage. Water needs to drain for the washer to move on. If it’s not going on, your system simply remains stuck.

To fix this, first check the water filter. Sometimes, it gets clogged, blocking off the water flow. If it is gunked up, cleaning it might sort things out. Replacing it is the only way to go if it’s too far gone.

Next, have a look at the drain line. Do you see any gaps or blockages there? If you do, repair them immediately. This can stop the water from getting out, preventing the washer system from moving on.

Then, take a look at the drain pump. It will not do its job well if it is clogged up. A proper cleansing may do the trick. But a brand new one might be in order if it is beyond that.

Lastly, the water inlet valve might be causing trouble. Clean it up if it is clogged with stuff it shouldn’t have. But if you have been facing the same problem for a long time, you should get it replaced.

2. Troubleshoot the Faulty Lid Switch

When your GE washer stops mid-cycle and doesn’t move, there’s a good chance the lid switch is malfunctioning. The lid switch is a safety device that stops the washer from agitating or spinning when the lid is raised.

You need to test the lid transfer. If you have one or can access it, use a digital multimeter.

Check if there’s a smooth flow of electricity while the lid switch is engaged. If it’s now not showing any signs of working, chances are it’s gone for good.

If it fails the multimeter test, you should get it replaced with a new one. This will ensure your washer doesn’t get stuck and continues running.

3. Defective Shift Actuator

When your GE washer cannot move from one cycle to the next, it might be an issue with a defective shift actuator. This important component is necessary for all the wash, rinse, and other cycles.

Run a diagnostic test to test if the shift actuator is the troublemaker. This test mainly examines the shift actuator’s capability within the washer’s system.

If the test highlights problems with this part, it indicates that it should be replaced.

By replacing the defective shift actuator with a brand new, functioning one, your washer will regain its ability to shift through cycles smoothly. This will ensure it doesn’t get caught and completes each phase as intended.

4. Timer Issue

Your timer is likely out of sync with your machine, causing it to get stuck. The proper functioning of the timer is necessary so that it shifts between cycles within a set time.

If you think that’s the case, it’s time for a timer replacement. By swapping out the faulty timer with a brand new one, your washer can sync back up, ensuring each cycle starts and finishes at the right time with no mix-up.

5. Incorrect Settings

If your GE washer appears stuck and won’t progress through its cycles, the problem is probably the incorrect settings.

If these are wrongly set, the washer will do just as directed. In this case, it could be running into some issue that prevents it from going forward in the sensing mode.

To solve this, test the settings. Make sure you’ve selected the right cycle for your laundry needs. If the settings are off, correct them.

If your washer continues to perform poorly, it’s time to reset. Zit will give your washer a clean start.

Unplug it for about a minute, then plug it back in. Once it’s on, open and close the lid six times within 12 seconds. This reset should get your washer back on track.

Frequently Asked Questions 

Why is my Deep Fill washer stuck on sensing?

If your Deep Fill washer is stuck on the sensing cycle, it could be due to various reasons. One possibility is a malfunctioning sensor or a clogged water inlet valve. Try unplugging the washer for a few minutes and then plug it back in to reset it. If the issue persists, it’s best to contact a professional technician for further assistance.

How do you reset a GE Deep Fill washing machine?

To reset a GE Deep Fill washing machine, start by unplugging the machine from the power source. Leave it unplugged for a couple of minutes. After that, plug it back in. Press the “Start/Pause” button for approximately five seconds to reset the machine. The display should be clear, indicating that the reset was successful.

What is Deep Fill on GE washer?

Deep Fill is a feature found in some GE washers that allow users to add additional water to the wash cycle. It provides a deeper water level for specific types of loads, such as heavily soiled or bulky items. This feature can be useful for achieving better cleaning results when needed. 

Conclusion

When your GE washer gets caught in sensing mode, it’s normally because of common problems like drainage issues, defective components, or settings going out of sync. 

You can fix these problems using simple fixes like unclogging drains, replacing faulty parts, or resetting the washer. These simple troubleshooting steps can save you from all issues on laundry day.